Tablettes professionnelles robustes et polyvalentes
Tablettes professionnelles robustes et polyvalentes
- Tablette avec Android (support jusqu'à Android 16) ou Windows (ET60W/ET65W)
- Écran WUXGA de 10,1 pouces avec 1 000 nits
- Qualcomm 6490 octa-core 2,7 GHz, 8 Go RAM, 128 Go Flash, Wi-Fi 6E et NFC ; ET65 : 5G, GPS
- Certifié IP66, MIL-STD-810H
- Batterie remplaçable à chaud de 8 920 mAh, batterie optionnelle de 17 840 mAh
Description
Description
Protection d'écran, Anti-choc IK06, transparent, compatible avec : ET60/ET65 (Android)
€34.99
€34.99
Hard-Wired Power Supply, Dual USB Type-A and Type-C Female ports Qualcomm Quick Charge 3.0, 5V/2.4A. 2 pin Molex port, with Molex 2 Pin cable and USB Type-C to USB Type-C cable
€54.61
€54.61
Active Holder, spring lock, USB-C 3.1, AMPS, VESA 75, order separately: charging solution, fits for: ET60, ET65 (Android)
€142.85
€142.85
Active Holder, lockable, USB-C 3.1, AMPS, VESA 75, order separately: charging solution, fits for: ET60, ET65 (Android)
€159.66
€159.66
Passive Holder, AMPS, VESA 75, color: black, fits for: ET60, ET65
€42.01
€42.01
Spring-Lock, acetal plastic, color: black, compatible with ET60/ET65 Brodit Holder
€33.61
€33.61
Locking Block with 2 keys, compatible with ET60/ET65 Brodit Holder
€42.01
€42.01
Holder, Key-Lock, USB-C 3.1, AMPS, VESA 75, order separately: Power Supply, for devices with standard or extended battery, fits for: ET60, ET65 Windows
€159.66
€159.66
Holder, Spring-Lock, USB-C 3.1, AMPS, VESA 75, order separately: Power Supply, for devices with standard and extended battery, fits for: ET60, ET65 Windows
€142.85
€142.85
Table stand contains five Brodit slide-in mounts, fits for: ET60/ET65
€605.03
€605.03
€20.74
€20.74
€81.72
€81.72
€10.98
€10.98
€263.46
€263.46
€326.41
Cet article sera retiré de la gamme ! Sécurisez les derniers restes de stock dès maintenant !
€326.41
€28.06
€28.06
Cig-Plug Adapter, USB-A and USB-C interface, Quick Charger 3.0, 5V, 2.4A, incl.: USB-C to USB-C cable
€33.61
€33.61
Wall Adapter, USB-C and USB-A Interface, Input: 220V, Output: 5V, 3A, Quick Charge, incl.: USB-C to USB-C cable
€46.21
€46.21
Battery Eliminator, no Cell Battery, fits for: ET60, ET65
€94.13
€94.13
Extended Battery, 17.840mAh, fits for: ET60, ET65
€227.89
€227.89
Standard Battery, 8920mAh, fits for: ET60, ET65
€128.81
€128.81
Battery Eliminator, no Cell Battery, fits for: ET6X (Windows)
€94.13
€94.13
Spare battery, 4460 mAh, fits for: ET6X (Windows)
€124.22
€124.22
Spare battery, extended, 8920 mAh, fits for: ET6X (Windows)
€219.77
€219.77
DC Power Adapter Cable from DC/DC Power Supply PS1370 to ET6 Vehicle Dock
€108.99
€108.99
Berceau Workstation Connect Zebra
€615.10
€615.10
Vehicle dock, IP66, interfaces: 2x USB-A (2.0), 1x RS232, drilling: VESA 100 x 100 / VESA 75 x 75, incl.: screws, lock and two keys, order separately: vehicle power supply, fits for: ET60/65
€881.86
€881.86
Vehicle dock, 2x USB-A, RS232, with RF pass through antennas, order separately: power supply, external antennas, fits for: ET6x
€980.94
€980.94
€9.42
€9.42
Keyboard support bracket, Keyboard VESA: 75x75, AMPS, cradle VESA: 100 x 100, 75 x 75, fits for: ET60, ET65 vehicle cradles
€178.35
€178.35
2-in-1 attachable rugged Keyboard, layout: DE, 78 keys, with multi-color dimmable backlight, fits for: ET60, ET65
€881.86
€881.86
2-in-1 attachable rugged Keyboard, layout: ES, 78 keys, with multi-color dimmable backlight, fits for: ET60, ET65
€881.86
€881.86
2-in-1 attachable rugged Keyboard, layout: FR, 78 keys, with multi-color dimmable backlight, fits for: ET60, ET65
€881.86
€881.86
2-in-1 attachable rugged Keyboard, layout: UK, 78 keys, with multi-color dimmable backlight, fits for: ET60, ET65
€881.86
€881.86
€881.86
€881.86
External Voltage Pre-Regulator (19-90V), 15 VDC out, 90 W
€592.77
€592.77
Zebra Power Supply, USB-C, 15V, 3A, 45W, order separately: Power Cord (C5), fits for: ET60, ET65, ET80, ET85
€54.31
€54.31
Cette station d'accueil de bureau Zebra comprend deux ports USB-C 2.0 et un port USB-A à l'arrière, vous permettant de connecter jusqu'à trois périphériques d'entrée tels qu'un clavier, une souris ou un scanner de codes-barres. Le port Ethernet RJ45 intégré fournit une connexion réseau sécurisée à haut débit, idéale pour l'accès en temps réel, les mises à jour à distance et la gestion des données de flotte pendant les temps d'arrêt de l'appareil.
Conçue pour optimiser l'espace, cette station d'accueil Zebra ET60/ET65 dispose d'un emplacement de montage spécialement conçu pour le chargeur de batterie OEM à 2 baies (vendu séparément), ce qui en fait un ajout polyvalent à tout poste de travail. Le support prend également en charge les appareils associés à des accessoires ergonomiques, sauf si le chargeur de batterie à 2 baies est installé, ce qui limite l'espace disponible.
Caractéristiques
Conçu spécifiquement pour les tablettes Zebra ET60, ET65, ET65W ; assure la charge via une connexion intégrée de broches pogo
Dispose du connecteur d'accueil breveté 3-D Float™
Le support prend en charge les appareils associés à des accessoires ergonomiques, sauf si le chargeur de batterie à 2 baies est installé
Zone de montage compatible avec le chargeur de batterie OEM Zebra à 2 baies (non inclus)
Dimensions du produit - Largeur totale 12", Hauteur totale 4,79", Profondeur totale 5,72"
Matériau(x) - Composite haute résistance, Acier inoxydable
Tension de sortie - 12V @ 3A
Puissance de sortie - 36 W
Ports - 2 x ports USB-C 2.0 (480 Mbps), 1 x port USB-A 2.0 (480 Mbps), 1 x port RJ45 (10/100 Mbps)
Réglementaire - FCC, CE, UKCA, RoHS, WEEE
Certifications - UL 62368-1
€573.91
€573.91
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablet with or without Zebra Keyboard.
To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.
The cut-outs on the buttons and ports allow you to continue using them without any problems.
The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.
The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.
An NFC repeater add-on module can be used to extend the device's internal NFC reader.
The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).
Product features RAM Mounts RAM-HOL-ZE25LU:
Compatible with Zebra Keyboard
Easy insertion and removal
Lockable with key
Additional mounting plate for attaching additional devices or accessories
Usable with RAM Vent-Temp, Temp Right, NFC-Repeater or Zebra CAC Reader
Additional information:
Devices shown are not included in the delivery.
Only the RAM-HOL-ZE25LU holder is supplied.
€297.44
€297.44
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.
The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.
This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.
To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.
The cut-outs on the buttons and ports allow you to continue using them without any problems.
The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.
The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.
An NFC repeater add-on module can be used to extend the device's internal NFC reader.
The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).
Product features RAM Mounts RAM-HOL-ZE25PD2HLU:
Compatible with Zebra Keyboard
Easy insertion and removal
Additional mounting plate for attaching additional devices or accessories
Usable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC Reader
Heated Pogo-Pins
Lockable with key
Input Connector: 5.5mm DC
Output Connector: 2x USB-A 2.0 (Peripheral output - 900mAh)
Transfer Speed: 12Mbps
Input Voltage: 12V
Input Cable Length: ca. 100 cm
Output Cable Length: ca. 25 cm
Certifications: RoHS, IC, FCC, WEEE, CE & UKCA
Additional information:
Devices shown are not included in the delivery.
Only the RAM-HOL-ZE25PD2HLU holder is supplied.
€596.60
€596.60
This RAM Mounts Form-Fit holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.
The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.
This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.
To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.
The cut-outs on the buttons and ports allow you to continue using them without any problems.
The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.
The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.
An NFC repeater add-on module can be used to extend the device's internal NFC reader.
The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).
Product features RAM Mounts RAM-HOL-ZE25PD2HU:
Compatible with Zebra Keyboard
Easy insertion and removal
Additional mounting plate for attaching additional devices or accessories
Usable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC Reader
Input Connector: 5.5mm DC
Output Connector: 2x USB-A 2.0 (Peripheral output - 900mAh)
Transfer Speed: 12Mbps
Input Voltage: 12V
Input Cable Length: ca. 100 cm
Output Cable Length: ca. 25 cm
Certifications: RoHS, IC, FCC, WEEE, CE & UKCA
Additional information:
Devices shown are not included in the delivery.
Only the RAM-HOL-ZE25PD2HU holder is supplied.
€548.70
€548.70
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.
The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in Dual USB Type-A cable.
To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.
The cut-outs on the buttons and ports allow you to continue using them without any problems.
The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.
The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.
An NFC repeater add-on module can be used to extend the device's internal NFC reader.
The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).
Product features RAM Mounts RAM-HOL-ZE25PD2LU:
Compatible with Zebra Keyboard
Easy insertion and removal
Additional mounting plate for attaching additional devices or accessories
Usable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC Reader
Lockable with key
Input Connector: 5.5mm DC
Output Connector: 2x USB-A 2.0 (Peripheral output - 900mAh)
Transfer Speed: 12Mbps
Input Voltage: 12V
Input Cable Length: ca. 100 cm
Output Cable Length: ca. 25 cm
Certifications: RoHS, IC, FCC, WEEE, CE & UKCA
Additional information:
Devices shown are not included in the delivery.
Only the RAM-HOL-ZE25PD2LU holder is supplied.
€493.24
€493.24
This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.
The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.
To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.
The cut-outs on the buttons and ports allow you to continue using them without any problems.
The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.
The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.
An NFC repeater add-on module can be used to extend the device's internal NFC reader.
The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).
Product features RAM Mounts RAM-HOL-ZE25PD2U:
Compatible with Zebra Keyboard
Easy insertion and removal
Additional mounting plate for attaching additional devices or accessories
Usable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC Reader
Input Connector: 5.5mm DC
Output Connector: USB-A 2.0 (Peripheral output - 900mAh per Port)
Transfer Speed: 12Mbps
Input Voltage: 12V
Input Cable Length: ca. 100 cm
Output Cable Length: ca. 25 cm
Certifications: RoHS, IC, FCC, WEEE, CE & UKCA
Additional information:
Devices shown are not included in the delivery.
Only the RAM-HOL-ZE25PD2U holder is supplied.
€441.13
€441.13
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.
The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.
This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.
To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.
The cut-outs on the buttons and ports allow you to continue using them without any problems.
The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.
The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.
An NFC repeater add-on module can be used to extend the device's internal NFC reader.
The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).
Product features RAM Mounts RAM-HOL-ZE25PDHLU:
Compatible with Zebra Keyboard
Easy insertion and removal
Additional mounting plate for attaching additional devices or accessories
Usable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC Reader
Heated Pogo-Pins
Lockable with key
Input Connector: 5.5mm DC
Output Connector: USB-A 2.0 (Peripheral output - 500mAh)
Transfer Speed: 12Mbps
Input Voltage: 12V
Input Cable Length: ca. 100 cm
Output Cable Length: ca. 25 cm
Certifications: RoHS, IC, FCC, WEEE, CE & UKCA
Additional information:
Devices shown are not included in the delivery.
Only the RAM-HOL-ZE25PDHLU holder is supplied.
€589.03
€589.03
This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.
The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.
This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.
To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.
The cut-outs on the buttons and ports allow you to continue using them without any problems.
The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.
The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.
An NFC repeater add-on module can be used to extend the device's internal NFC reader.
The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).
Product features RAM Mounts RAM-HOL-ZE25PDHU:
Compatible with Zebra Keyboard
Easy insertion and removal
With Latch
Additional mounting plate for attaching additional devices or accessories
Usable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC Reader
Input Connector: 5.5mm DC
Output Connector: USB-A 2.0 (Peripheral output - 500mAh)
Transfer Speed: 12Mbps
Input Voltage: 12V
Input Cable Length: ca. 100 cm
Output Cable Length: ca. 25 cm
Certifications: RoHS, IC, FCC, WEEE, CE & UKCA
Additional information:
Devices shown are not included in the delivery.
Only the RAM-HOL-ZE25PDHU holder is supplied.
€539.45
€539.45
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.
The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.
To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.
The cut-outs on the buttons and ports allow you to continue using them without any problems.
The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.
The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.
An NFC repeater add-on module can be used to extend the device's internal NFC reader.
The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).
Product features RAM Mounts RAM-HOL-ZE25PDLU:
Compatible with Zebra Keyboard
Easy insertion and removal
Additional mounting plate for attaching additional devices or accessories
Usable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC Reader
Lockable with key
Input Connector: 5.5mm DC
Output Connector: USB-A 2.0 (Peripheral output - 500mAh)
Transfer Speed: 12Mbps
Input Voltage: 12V
Input Cable Length: ca. 100 cm
Output Cable Length: ca. 25 cm
Certifications: RoHS, IC, FCC, WEEE, CE & UKCA
Additional information:
Devices shown are not included in the delivery.
Only the RAM-HOL-ZE25PDLU holder is supplied.
€471.39
€471.39
This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.
The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.
To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.
The cut-outs on the buttons and ports allow you to continue using them without any problems.
The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.
The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.
An NFC repeater add-on module can be used to extend the device's internal NFC reader.
The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).
Product features RAM Mounts RAM-HOL-ZE25PDU:
Compatible with Zebra Keyboard
Easy insertion and removal
With Latch
Additional mounting plate for attaching additional devices or accessories
Usable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC Reader
Input Connector: 5.5mm DC
Output Connector: USB-A 2.0 (Peripheral output - 500mAh)
Transfer Speed: 12Mbps
Input Voltage: 12V
Input Cable Length: ca. 100 cm
Output Cable Length: ca. 25 cm
Certifications: RoHS, IC, FCC, WEEE, CE & UKCA
Additional information:
Devices shown are not included in the delivery.
Only the RAM-HOL-ZE25PDU holder is supplied.
€426.01
€426.01
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.
The holder is powered by a 5.5mm DC connection and charges the device in the dock.
This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.
To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.
The cut-outs on the buttons and ports allow you to continue using them without any problems.
The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.
The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.
An NFC repeater add-on module can be used to extend the device's internal NFC reader.
The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).
Product features RAM Mounts RAM-HOL-ZE25PHLU:
Compatible with Zebra Keyboard
Easy insertion and removal
Additional mounting plate for attaching additional devices or accessories
Usable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC Reader
Heated Pogo-Pins
Lockable with key
Input Connector: 5.5mm DC
Input Voltage: 12V
Input Cable Length: ca. 100 cm
Certifications: RoHS, IC, FCC, WEEE, CE & UKCA
Additional information:
Devices shown are not included in the delivery.
Only the RAM-HOL-ZE25PHLU holder is supplied.
€449.54
€449.54
This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.
The holder is powered by a 5.5mm DC connection and charges the device in the dock.
This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.
To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.
The cut-outs on the buttons and ports allow you to continue using them without any problems.
The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.
The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.
An NFC repeater add-on module can be used to extend the device's internal NFC reader.
The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).
Product features RAM Mounts RAM-HOL-ZE25PHU:
Compatible with Zebra Keyboard
Easy insertion and removal
With Latch
Additional mounting plate for attaching additional devices or accessories
Usable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC Reader
Heated Pogo-Pins
Input Connector: 5.5mm DC
Input Voltage: 12V
Input Cable Length: ca. 100 cm
Certifications: RoHS, IC, FCC, WEEE, CE & UKCA
Additional information:
Devices shown are not included in the delivery.
Only the RAM-HOL-ZE25PHU holder is supplied.
€402.48
€402.48
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.
The holder is powered by a 5.5mm DC connection and charges the device in the dock.
To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.
The cut-outs on the buttons and ports allow you to continue using them without any problems.
The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.
The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.
An NFC repeater add-on module can be used to extend the device's internal NFC reader.
The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).
Product features RAM Mounts RAM-HOL-ZE25PLU:
Compatible with Zebra Keyboard
Easy insertion and removal
Additional mounting plate for attaching additional devices or accessories
Usable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC Reader
Lockable with key
Input Connector: 5.5mm DC
Input Voltage: 12V
Input Cable Length: ca. 100 cm
Certifications: RoHS, IC, FCC, WEEE, CE & UKCA
Additional information:
Devices shown are not included in the delivery.
Only the RAM-HOL-ZE25PLU holder is supplied.
€386.51
€386.51
This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.
The holder is powered by a 5.5mm DC connection and charges the device in the dock.
To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.
The cut-outs on the buttons and ports allow you to continue using them without any problems.
The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.
The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.
An NFC repeater add-on module can be used to extend the device's internal NFC reader.
The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).
Product features RAM Mounts RAM-HOL-ZE25PU:
Compatible with Zebra Keyboard
Easy insertion and removal
With Latch
Additional mounting plate for attaching additional devices or accessories
Usable with RAM Vent-Temp, Temp Right, NFC-Repeater or Zebra CAC Reader
Input Connector: 5.5mm DC
Input Voltage: 12V
Input Cable Length: ca. 100 cm
Certifications: RoHS, IC, FCC, WEEE, CE & UKCA
Additional information:
Devices shown are not included in the delivery.
Only the RAM-HOL-ZE25PU holder is supplied.
€342.82
€342.82
This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 & ET65 Tablet with or without Zebra Keyboard.
To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.
The cut-outs on the buttons and ports allow you to continue using them without any problems.
The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.
The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.
An NFC repeater add-on module can be used to extend the device's internal NFC reader.
The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).
Product features RAM Mounts RAM-HOL-ZE25U:
Compatible with Zebra Keyboard
Easy insertion and removal
With Latch
Additional mounting plate for attaching additional devices or accessories
Usable with RAM Vent-Temp, Temp Right, NFC-Repeater or Zebra CAC Reader
Additional information:
Devices shown are not included in the delivery.
Only the RAM-HOL-ZE25U holder is supplied.
€251.22
€251.22
2-Slot Battery Charger, order separately: Power Supply, AC and DC Cable, fits for: ET6X
€227.89
€227.89
€66.11
€66.11
€21.40
€21.40
€49.89
€49.89
€124.73
€124.73
Stylet, lot de 3, pointe en fibre, compatible avec : MC22, MC27, TC21, TC26, TC22, TC27, TC52x, TC52ax, TC73, TC78, ET60, ET65, TC501
€30.26
€30.26
€56.75
€56.75
Jarltech Premium Service for Project Business
€3.00
€3.00
Contact us and book our Staging Premium Service
€240.00
€240.00
Kickstand with Rotating Hand Strap, Hand Strap is adjustable and rotatable, compatible with standard and extended battery, fits for: ET60, ET65
€168.44
€168.44
Service OneCare Essential, comprehensive, 3 day TAT, purchased in 30 days, 3 years, fits for: ET60, ET65 (Windows)
€460.30
€460.30
Service OneCare Essential, comprehensive, 3 day TAT, purchased in 30 days, 5 years, fits for: ET60, ET65 (Windows)
€767.16
€767.16
Service OneCare Essential, comprehensive, 3 day TAT, purchased in 30 days, 3 years, fits for: ET60, ET65
€316.07
€316.07
Service OneCare Essential, comprehensive, 3 day TAT, purchased in 30 days, 5 years, fits for: ET60, ET65 (Android)
€526.79
€526.79
Service One Care Essential, 7 years, 3 days TAT, purchased within 30 days, with comprehensive coverage, proactive battery replacement for battery in use, fits for: ET6xxx
€856.47
€856.47
Fiche technique & plus
* La réduction s'applique au prix de vente initial.