- Wytrzymały tablet 2 w 1 z odłączaną klawiaturą
- 12-calowy wyświetlacz dotykowy QHD o jasności 800 nitów i szkle Corning Gorilla Glass
- 11. generacja procesorów Intel Core i5/i7, bateria litowo-polimerowa 5180 mAh
- Certyfikat IP65 i e-Mark, odporny na uderzenia z wysokości do 1,5 m (z osłoną ochronną)
- USB-C, Wi-Fi 6, Bluetooth 5.2, NFC i opcjonalny Ethernet; ET85: 5G i GPS
Product detail sub menu
Description
Description
Dodatkowe wyposażenie ET80/ET85 obejmuje wydajne procesory Intel Core i5 lub i7 11. generacji, a także 8 lub 16 GB pamięci RAM oraz dyski SSD o pojemności 128, 256 lub 512 GB. Wymienny akumulator litowo-jonowy o pojemności 5180 mAh z technologią PowerPrecision+ zapewnia długi czas pracy. Opcjonalnie dostępny jest akumulator hot-swap o pojemności 3400 mAh z czasem pracy do 11 godzin. Ponadto tablety oferują przednią kamerę Windows Hello o rozdzielczości 5 megapikseli oraz tylną kolorową kamerę z autofokusem o rozdzielczości 13 megapikseli z kontrolowaną przez użytkownika lampą błyskową LED. W zależności od potrzeb dostępne są również zintegrowany skaner 2D z silnikiem skanującym SE4107 i czytnik linii papilarnych Windows Hello. Skaner, który odczytuje również słabo wydrukowane, uszkodzone i porysowane kody kreskowe, znajduje się w prawym dolnym rogu tabletów ET80/ET85. Personel służb publicznych ma dzięki temu możliwość łatwiejszego skanowania dokumentów, nawet gdy tablet jest zadokowany w pojeździe.
Szeroki wybór interfejsów zapewnia płynny transfer danych i wysoką łączność. Obejmuje on USB-A 3.2, USB-C, Wi-Fi 6, Bluetooth 5.2, NFC oraz opcjonalnie Ethernet. ET85 dodatkowo oferuje łączność 5G i GPS, a także nano- i eSIM. Tablety są wyposażone w dwa głośniki i cztery mikrofony z funkcją redukcji szumów. Niezależnie od tego, czy chodzi o rozmowę typu push-to-talk, połączenie wideo, dyktowanie notatek, czy korzystanie z komend głosowych – każde słowo jest rozumiane. Podczas projektowania tabletów 2 w 1 ET80/ET85 firma Zebra postawiła na konstrukcję bez wentylatorów o wysokiej wytrzymałości. Są one w pełni chronione przed kurzem i strumieniami wody zgodnie ze standardem IP65 i są odporne na uderzenia zgodnie z normami MIL-STD-810H i MIL-STD 461G z wysokości do 1,2 m lub 1,5 m z opcjonalną osłoną ochronną. Dzięki certyfikatowi Class 1 Division 2 tablety ET80 i ET85 mogą być również bezpiecznie stosowane w pobliżu łatwopalnych materiałów niebezpiecznych.
Aby uzyskać jeszcze większą wydajność i zwiększyć efektywność, tablety ET80/ET85 korzystają z narzędzi Zebra Mobility DNA i Scanning DataCapture DNA. Należą do nich Workforce Connect z różnymi funkcjami push-to-talk i wysyłania wiadomości tekstowych oraz 123Scan do automatycznego rozpoznawania i uproszczonej konfiguracji zintegrowanego skanera.
(brd216229 – 216229)
€67.22
€67.22
(brd217039 – 217039)
Holder, Key-Lock, USB-C 3.1, AMPS, VESA 75, order separately: Power Supply, fits for: ET80, ET85
€168.06
€168.06
(brd217040 – 217040)
Holder, Spring-Lock, USB-C 3.1, AMPS, VESA 75, order separately: Power Supply, fits for: ET80, ET85
€151.25
€151.25
(zcabadap – 450143)
€26.72
€26.72
(brd710296 – 710296)
€159.66
€159.66
(brd710297 – 710297)
€142.85
€142.85
(brd710301 – 710301)
€134.45
€134.45
(brd710302 – 710302)
€117.64
€117.64
(brd739296 – 739296)
€218.48
€218.48
(brd739297 – 739297)
€201.67
€201.67
(brd739301 – 739301)
€184.87
€184.87
(brd739302 – 739302)
€176.46
€176.46
(brd741296 – 741296)
€201.67
€201.67
(brd741297 – 741297)
€184.87
€184.87
(brd741301 – 741301)
€176.46
€176.46
(brd741302 – 741302)
€159.66
€159.66
(zet80bat – BTRY-ET8X-12IN1-01)
€166.34
€166.34
(zet80bat2 – BTRY-ET8X-PRPK1-01)
€256.07
€256.07
(zet80rj45cab – CBL-ET8X-E1-01)
€47.51
€47.51
(zet80dock9 – CRD-ET8X-M-9PEM1-01)
€594.00
€594.00
(zet80dockfan – CRD-ET8X-M-FAN1-01)
€237.62
€237.62
(zet80dockbra – CRD-ET8X-M-KBBK1-01)
Keyboard Bracket (without screws), fits for: ET8X
€225.72
€225.72
(zet80dockcov – CRD-ET8X-M-PEMCV1-01)
€95.05
€95.05
(zet80dockant – CRD-ET8X-M-PTA1-01)
€380.17
€380.17
(zet80offdock – CRD-ET8X-OFFDK1-01)
€950.39
€950.39
(zet80pdock – CRD-ET8X-PWRDK1-01)
€475.20
€475.20
(zet80vdock – CRD-ET8X-VEHDK1-01)
€772.20
€772.20
(zet80keybde – KYB-ET8X-2IN1-DE1-01)
€534.61
€534.61
(zet80keybes – KYB-ET8X-2IN1-ES1-01)
€534.61
€534.61
(zet80keybfr – KYB-ET8X-2IN1-FR1-01)
€534.61
€534.61
(zet80keybnor – KYB-ET8X-2IN1-NO1-01)
Keyboard, 2-in-1, layout: Nordic, 82 keys, multi-color backlight, 6 additional programable keys, fits for: ET8X
€474.89
€474.89
(zet80keybuk – KYB-ET8X-2IN1-UK1-01)
€534.61
€534.61
(zet80keybus – KYB-ET8X-2IN1-US1-01)
€534.61
€534.61
(zet80batdoor – MISC-ET8X-BTDR1-01)
€47.51
€47.51
(zet80ps-2 – PWR-BGA15V45W-UC2-WW)
Zebra Power Supply, USB-C, 15V, 3A, 45W, order separately: Power Cord (C5), fits for: ET60, ET65, ET80, ET85
€51.72
€51.72
(ramholder63 – RAM-HOL-ZE22LU)
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET80 & ET85 2-in-1 Tablet with or without Rugged Boot and Keyboard.
To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.
The cut-outs on the buttons and ports allow you to continue using them without any problems.
The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.
The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.
An NFC repeater add-on module can be used to extend the device's internal NFC reader.
The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).
Product features RAM Mounts RAM-HOL-ZE22LU:
Compatible with accessories
Easy insertion and removal
Lockable with key
Additional mounting plate for attaching additional devices or accessories
Usable with RAM Vent-Temp, Temp Right or NFC-Repeater
Additional information:
Devices shown are not included in the delivery.
Only the RAM-HOL-ZE22LU holder is supplied.
€276.43
€276.43
(ramholze22pd2lu – RAM-HOL-ZE22PD2LU)
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET8x 2-in-1 Tablet with or without Rugged Boot and Keyboard.
The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in Dual USB Type-A cable.
To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.
The cut-outs on the buttons and ports allow you to continue using them without any problems.
The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.
The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.
An NFC repeater add-on module can be used to extend the device's internal NFC reader.
The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).
Product features RAM Mounts RAM-HOL-ZE22PD2LU:
Compatible with accessories
Easy insertion and removal
Additional mounting plate for attaching additional devices or accessories
Usable with RAM Vent-Temp, Temp-Right or NFC-Repeater
Lockable with key
Input Connector: 5.5mm DC
Output Connector: 2x USB-A 2.0 (Peripheral output - 900mAh)
Transfer Speed: 12Mbps
Input Cable Length: ca. 100 cm
Output Cable Length: ca. 24 cm
Certifications: RoHS, WEEE, CE & UKCA
Additional information:
Devices shown are not included in the delivery.
Only the RAM-HOL-ZE22PD2LU holder is supplied.
€456.26
€456.26
(ramholder51 – RAM-HOL-ZE22PD2U)
This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET8x 2-in-1 Tablet with or without Rugged Boot and Keyboard.
The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.
To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.
The cut-outs on the buttons and ports allow you to continue using them without any problems.
The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.
The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.
An NFC repeater add-on module can be used to extend the device's internal NFC reader.
The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).
Product features RAM Mounts RAM-HOL-ZE22PD2U:
Compatible with accessories
Easy insertion and removal
Additional mounting plate for attaching additional devices or accessories
Usable with RAM Vent-Temp, Temp- Right or NFC-Repeater
Input Connector: 5.5mm DC
Output Connector: USB-A 2.0 (Peripheral output - 900mAh per Port)
Transfer Speed: 12Mbps
Input Cable Length: ca. 100 cm
Output Cable Length: ca. 24 cm
Certifications: RoHS, WEEE, CE & UKCA
Additional information:
Devices shown are not included in the delivery.
Only the RAM-HOL-ZE22PD2U holder is supplied.
€406.68
€406.68
(ramholder57 – RAM-HOL-ZE22PDLU)
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET8x 2-in-1 Tablet with or without Rugged Boot and Keyboard.
The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.
To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.
The cut-outs on the buttons and ports allow you to continue using them without any problems.
The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.
The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.
An NFC repeater add-on module can be used to extend the device's internal NFC reader.
The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).
Product features RAM Mounts RAM-HOL-ZE22PDLU:
Compatible with accessories
Easy insertion and removal
Additional mounting plate for attaching additional devices or accessories
Usable with RAM Vent-Temp, Temp-Right or NFC-Repeater
Lockable with key
Input Connector: 5.5mm DC
Output Connector: USB-A 2.0 (Peripheral output - 500mAh)
Transfer Speed: 12Mbps
Input Cable Length: ca. 100 cm
Output Cable Length: ca. 24 cm
Certifications: RoHS, WEEE, CE & UKCA
Additional information:
Devices shown are not included in the delivery.
Only the RAM-HOL-ZE22PDLU holder is supplied.
€414.24
€414.24
(ramholze22pdu – RAM-HOL-ZE22PDU)
This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET8x 2-in-1 Tablet with or without Rugged Boot and Keyboard.
The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.
To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.
The cut-outs on the buttons and ports allow you to continue using them without any problems.
The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.
The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.
An NFC repeater add-on module can be used to extend the device's internal NFC reader.
The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).
Product features RAM Mounts RAM-HOL-ZE22PDU:
Compatible with accessories
Easy insertion and removal
With Latch
Additional mounting plate for attaching additional devices or accessories
Usable with RAM Vent-Temp, Temp- Right or NFC-Repeater
Input Connector: 5.5mm DC
Output Connector: USB-A 2.0 (Peripheral output - 500mAh)
Transfer Speed: 12Mbps
Input Cable Length: ca. 100 cm
Output Cable Length: ca. 24 cm
Certifications: RoHS, WEEE, CE & UKCA
Additional information:
Devices shown are not included in the delivery.
Only the RAM-HOL-ZE22PDU holder is supplied.
€368.03
€368.03
(ramholder103 – RAM-HOL-ZE22PLU)
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET80 & ET85 2-in-1 Tablet with or without Rugged Boot and Keyboard.
The holder is powered by a 5.5mm DC connection and charges the device in the dock.
To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.
The cut-outs on the buttons and ports allow you to continue using them without any problems.
The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.
The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.
An NFC repeater add-on module can be used to extend the device's internal NFC reader.
The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).
Product features RAM Mounts RAM-HOL-ZE22PLU:
Compatible with accessories
Easy insertion and removal
Additional mounting plate for attaching additional devices or accessories
Usable with RAM Vent-Temp, Temp Right or NFC-Repeater
Lockable with key
Input Connector: 5.5mm DC
Input Cable Length: ca. 100 cm
Certifications: RoHS, WEEE, CE & UKCA
Additional information:
Devices shown are not included in the delivery.
Only the RAM-HOL-ZE22PLU holder is supplied.
€348.70
€348.70
(ramet8dock – RAM-HOL-ZE22PU)
This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET80 & ET85 2-in-1 Tablet with or without Rugged Boot and Keyboard.
The holder is powered by a 5.5mm DC connection and charges the device in the dock.
To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.
The cut-outs on the buttons and ports allow you to continue using them without any problems.
The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.
The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.
An NFC repeater add-on module can be used to extend the device's internal NFC reader.
The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).
Product features RAM Mounts RAM-HOL-ZE22PU:
Compatible with accessories
Easy insertion and removal
With Latch
Additional mounting plate for attaching additional devices or accessories
Usable with RAM Vent-Temp, Temp Right or NFC-Repeater
Input Connector: 5.5mm DC
Input Cable Length: ca. 100 cm
Certifications: RoHS, WEEE, CE & UKCA
Additional information:
Devices shown are not included in the delivery.
Only the RAM-HOL-ZE22PU holder is supplied.
€299.96
€299.96
(ramet8tab – RAM-HOL-ZE22U)
This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET80 & ET85 2-in-1 Tablet with or without Rugged Frame and Keyboard.
To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.
The cut-outs on the buttons and ports allow you to continue using them without any problems.
The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.
The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.
An NFC repeater add-on module can be used to extend the device's internal NFC reader.
The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).
Product features RAM Mounts RAM-HOL-ZE22U:
Compatible with accessories
Easy insertion and removal
With Latch
Additional mounting plate for attaching additional devices or accessories
Usable with RAM Vent-Temp, Temp Right or NFC-Repeater
Additional information:
Devices shown are not included in the delivery.
Only the RAM-HOL-ZE22U holder is supplied.
€231.05
€231.05
(syet5chg4 – SAC-ET5X-4PPK1-01)
PowerPack battery charging station, 4 slots, order separately: power supply, DC cable, power cord, fits for: ET5X, ET4X & ET8X PowerPack
€162.17
€162.17
(zet80boot – SG-ET8X-BOOT1-01)
€237.62
€237.62
(zet80handle – SG-ET8X-HANDLE1-01)
€62.96
€62.96
(zet80sph – SG-ET8X-PENLOOP1-01)
€20.38
€20.38
(zet80sstrap – SG-ET8X-SHLDR1-01)
€47.51
€47.51
(zet80stlyus – SG-ET8X-STYLUS1-01)
Stylus, long, order separately: tether, fits for: L10ax
€118.79
€118.79
(stageit-l – Stageit-l)
Contact us and book our Staging Premium Service
€60.00
€60.00
(stageit-m – Stageit-m)
Contact us and book our Staging Premium Service
€30.00
€30.00
(stageit-s – Stageit-s)
Contact us and book our Staging Premium Service
€10.00
€10.00
(stageit-xl – Stageit-xl)
Contact us and book our Staging Premium Service
€240.00
€240.00
(syaeet8x-3c – Z1AE-ET8XXX-3C00)
€238.88
€238.88
Data sheet & more
* The discount refers to the original sales price.