- Tableta robusta 2 en 1 con teclado extraíble
- Pantalla táctil QHD de 12" con 800 nits y Corning Gorilla Glass
- Procesadores Intel Core i5/i7 de 11.ª generación, batería de polímero de litio de 5.180 mAh
- Certificado IP65 y e-Mark, resistente a impactos hasta 1,5 m (con cubierta protectora)
- USB-C, Wi-Fi 6, Bluetooth 5.2, NFC y Ethernet opcional; ET85: 5G y GPS
Description
Description
Otros equipos de las ET80/ET85 incluyen potentes procesadores Intel Core i5 o i7 de 11ª generación, así como 8 o 16 GB de memoria RAM y 128, 256 o 512 GB de SSD. La batería reemplazable de iones de litio de 5.180 mAh con tecnología PowerPrecision+ garantiza largos tiempos de actividad. Opcionalmente, está disponible una batería hot-swap de 3.400 mAh con hasta 11 horas de autonomía. Además, las tabletas ofrecen una cámara frontal de 5 megapíxeles con Windows Hello y una cámara trasera a color de 13 megapíxeles con autoenfoque y flash LED controlado por el usuario. Dependiendo de los requisitos, también hay disponible un escáner 2D integrado con motor de escaneo SE4107 y un lector de huellas dactilares con Windows Hello. El escáner, que también lee códigos de barras mal impresos, dañados y rayados, se encuentra en la esquina inferior derecha de las tabletas ET80/ET85. Para el personal de servicios públicos, esto ofrece la ventaja de escanear documentos más fácilmente, incluso cuando la tableta está conectada en el vehículo.
La gran selección de interfaces garantiza una transferencia de datos fluida y una alta conectividad. Esto consiste en USB-A 3.2, USB-C, Wi-Fi 6, Bluetooth 5.2, NFC y Ethernet opcional. La ET85 ofrece además 5G y GPS, así como una nano SIM y eSIM. Las tabletas están equipadas con dos altavoces y cuatro micrófonos con cancelación de ruido. Ya sea durante una llamada push-to-talk o una videollamada, dictando notas o usando comandos de voz, cada palabra se entiende. Durante el diseño de las tabletas 2 en 1 ET80/ET85, Zebra se centró en un diseño sin ventilador con alta durabilidad. Están completamente protegidas contra el polvo y los chorros de agua según las normas IP65 y son resistentes a los impactos de acuerdo con MIL-STD-810H y MIL-STD 461G desde hasta 1,2 m o 1,5 m con la cubierta protectora opcional. Gracias a la certificación Class 1 Division 2, las tabletas ET80 y ET85 también pueden utilizarse de forma segura en las proximidades de materiales peligrosos inflamables.
Para un rendimiento aún mayor y una mayor eficiencia, las tabletas ET80/ET85 acceden a las herramientas Zebra Mobility DNA y Scanning DataCapture DNA. Estas incluyen Workforce Connect con varias funciones de push-to-talk y mensajería de texto, y 123Scan para el reconocimiento automatizado y la configuración simplificada del escáner integrado.
(brd216229 – 216229)
€67.22
€67.22
(brd217039 – 217039)
Holder, Key-Lock, USB-C 3.1, AMPS, VESA 75, order separately: Power Supply, fits for: ET80, ET85
€168.06
€168.06
(brd217040 – 217040)
Holder, Spring-Lock, USB-C 3.1, AMPS, VESA 75, order separately: Power Supply, fits for: ET80, ET85
€151.25
€151.25
(zcabadap – 450143)
€26.72
€26.72
(brd710296 – 710296)
€159.66
€159.66
(brd710297 – 710297)
€142.85
€142.85
(brd710301 – 710301)
€134.45
€134.45
(brd710302 – 710302)
€117.64
€117.64
(brd739296 – 739296)
€218.48
€218.48
(brd739297 – 739297)
€201.67
€201.67
(brd739301 – 739301)
€184.87
€184.87
(brd739302 – 739302)
€176.46
€176.46
(brd741296 – 741296)
€201.67
€201.67
(brd741297 – 741297)
€184.87
€184.87
(brd741301 – 741301)
€176.46
€176.46
(brd741302 – 741302)
€159.66
€159.66
(zet80bat – BTRY-ET8X-12IN1-01)
€166.34
€166.34
(zet80bat2 – BTRY-ET8X-PRPK1-01)
€256.07
€256.07
(zet80rj45cab – CBL-ET8X-E1-01)
€47.51
€47.51
(zet80dock9 – CRD-ET8X-M-9PEM1-01)
€594.00
€594.00
(zet80dockfan – CRD-ET8X-M-FAN1-01)
€237.62
€237.62
(zet80dockbra – CRD-ET8X-M-KBBK1-01)
Keyboard Bracket (without screws), fits for: ET8X
€225.72
€225.72
(zet80dockcov – CRD-ET8X-M-PEMCV1-01)
€95.05
€95.05
(zet80dockant – CRD-ET8X-M-PTA1-01)
€380.17
€380.17
(zet80offdock – CRD-ET8X-OFFDK1-01)
€950.39
€950.39
(zet80pdock – CRD-ET8X-PWRDK1-01)
€475.20
€475.20
(zet80vdock – CRD-ET8X-VEHDK1-01)
€772.20
€772.20
(zet80keybde – KYB-ET8X-2IN1-DE1-01)
€534.61
€534.61
(zet80keybes – KYB-ET8X-2IN1-ES1-01)
€534.61
€534.61
(zet80keybfr – KYB-ET8X-2IN1-FR1-01)
€534.61
€534.61
(zet80keybnor – KYB-ET8X-2IN1-NO1-01)
Keyboard, 2-in-1, layout: Nordic, 82 keys, multi-color backlight, 6 additional programable keys, fits for: ET8X
€474.89
€474.89
(zet80keybuk – KYB-ET8X-2IN1-UK1-01)
€534.61
€534.61
(zet80keybus – KYB-ET8X-2IN1-US1-01)
€534.61
€534.61
(zet80batdoor – MISC-ET8X-BTDR1-01)
€47.51
€47.51
(zet80ps-2 – PWR-BGA15V45W-UC2-WW)
Zebra Power Supply, USB-C, 15V, 3A, 45W, order separately: Power Cord (C5), fits for: ET60, ET65, ET80, ET85
€51.72
€51.72
(ramholder63 – RAM-HOL-ZE22LU)
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET80 & ET85 2-in-1 Tablet with or without Rugged Boot and Keyboard.
To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.
The cut-outs on the buttons and ports allow you to continue using them without any problems.
The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.
The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.
An NFC repeater add-on module can be used to extend the device's internal NFC reader.
The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).
Product features RAM Mounts RAM-HOL-ZE22LU:
Compatible with accessories
Easy insertion and removal
Lockable with key
Additional mounting plate for attaching additional devices or accessories
Usable with RAM Vent-Temp, Temp Right or NFC-Repeater
Additional information:
Devices shown are not included in the delivery.
Only the RAM-HOL-ZE22LU holder is supplied.
€276.43
€276.43
(ramholze22pd2lu – RAM-HOL-ZE22PD2LU)
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET8x 2-in-1 Tablet with or without Rugged Boot and Keyboard.
The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in Dual USB Type-A cable.
To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.
The cut-outs on the buttons and ports allow you to continue using them without any problems.
The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.
The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.
An NFC repeater add-on module can be used to extend the device's internal NFC reader.
The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).
Product features RAM Mounts RAM-HOL-ZE22PD2LU:
Compatible with accessories
Easy insertion and removal
Additional mounting plate for attaching additional devices or accessories
Usable with RAM Vent-Temp, Temp-Right or NFC-Repeater
Lockable with key
Input Connector: 5.5mm DC
Output Connector: 2x USB-A 2.0 (Peripheral output - 900mAh)
Transfer Speed: 12Mbps
Input Cable Length: ca. 100 cm
Output Cable Length: ca. 24 cm
Certifications: RoHS, WEEE, CE & UKCA
Additional information:
Devices shown are not included in the delivery.
Only the RAM-HOL-ZE22PD2LU holder is supplied.
€456.26
€456.26
(ramholder51 – RAM-HOL-ZE22PD2U)
This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET8x 2-in-1 Tablet with or without Rugged Boot and Keyboard.
The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.
To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.
The cut-outs on the buttons and ports allow you to continue using them without any problems.
The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.
The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.
An NFC repeater add-on module can be used to extend the device's internal NFC reader.
The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).
Product features RAM Mounts RAM-HOL-ZE22PD2U:
Compatible with accessories
Easy insertion and removal
Additional mounting plate for attaching additional devices or accessories
Usable with RAM Vent-Temp, Temp- Right or NFC-Repeater
Input Connector: 5.5mm DC
Output Connector: USB-A 2.0 (Peripheral output - 900mAh per Port)
Transfer Speed: 12Mbps
Input Cable Length: ca. 100 cm
Output Cable Length: ca. 24 cm
Certifications: RoHS, WEEE, CE & UKCA
Additional information:
Devices shown are not included in the delivery.
Only the RAM-HOL-ZE22PD2U holder is supplied.
€406.68
€406.68
(ramholder57 – RAM-HOL-ZE22PDLU)
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET8x 2-in-1 Tablet with or without Rugged Boot and Keyboard.
The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.
To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.
The cut-outs on the buttons and ports allow you to continue using them without any problems.
The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.
The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.
An NFC repeater add-on module can be used to extend the device's internal NFC reader.
The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).
Product features RAM Mounts RAM-HOL-ZE22PDLU:
Compatible with accessories
Easy insertion and removal
Additional mounting plate for attaching additional devices or accessories
Usable with RAM Vent-Temp, Temp-Right or NFC-Repeater
Lockable with key
Input Connector: 5.5mm DC
Output Connector: USB-A 2.0 (Peripheral output - 500mAh)
Transfer Speed: 12Mbps
Input Cable Length: ca. 100 cm
Output Cable Length: ca. 24 cm
Certifications: RoHS, WEEE, CE & UKCA
Additional information:
Devices shown are not included in the delivery.
Only the RAM-HOL-ZE22PDLU holder is supplied.
€414.24
€414.24
(ramholze22pdu – RAM-HOL-ZE22PDU)
This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET8x 2-in-1 Tablet with or without Rugged Boot and Keyboard.
The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.
To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.
The cut-outs on the buttons and ports allow you to continue using them without any problems.
The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.
The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.
An NFC repeater add-on module can be used to extend the device's internal NFC reader.
The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).
Product features RAM Mounts RAM-HOL-ZE22PDU:
Compatible with accessories
Easy insertion and removal
With Latch
Additional mounting plate for attaching additional devices or accessories
Usable with RAM Vent-Temp, Temp- Right or NFC-Repeater
Input Connector: 5.5mm DC
Output Connector: USB-A 2.0 (Peripheral output - 500mAh)
Transfer Speed: 12Mbps
Input Cable Length: ca. 100 cm
Output Cable Length: ca. 24 cm
Certifications: RoHS, WEEE, CE & UKCA
Additional information:
Devices shown are not included in the delivery.
Only the RAM-HOL-ZE22PDU holder is supplied.
€368.03
€368.03
(ramholder103 – RAM-HOL-ZE22PLU)
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET80 & ET85 2-in-1 Tablet with or without Rugged Boot and Keyboard.
The holder is powered by a 5.5mm DC connection and charges the device in the dock.
To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.
The cut-outs on the buttons and ports allow you to continue using them without any problems.
The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.
The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.
An NFC repeater add-on module can be used to extend the device's internal NFC reader.
The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).
Product features RAM Mounts RAM-HOL-ZE22PLU:
Compatible with accessories
Easy insertion and removal
Additional mounting plate for attaching additional devices or accessories
Usable with RAM Vent-Temp, Temp Right or NFC-Repeater
Lockable with key
Input Connector: 5.5mm DC
Input Cable Length: ca. 100 cm
Certifications: RoHS, WEEE, CE & UKCA
Additional information:
Devices shown are not included in the delivery.
Only the RAM-HOL-ZE22PLU holder is supplied.
€348.70
€348.70
(ramet8dock – RAM-HOL-ZE22PU)
This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET80 & ET85 2-in-1 Tablet with or without Rugged Boot and Keyboard.
The holder is powered by a 5.5mm DC connection and charges the device in the dock.
To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.
The cut-outs on the buttons and ports allow you to continue using them without any problems.
The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.
The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.
An NFC repeater add-on module can be used to extend the device's internal NFC reader.
The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).
Product features RAM Mounts RAM-HOL-ZE22PU:
Compatible with accessories
Easy insertion and removal
With Latch
Additional mounting plate for attaching additional devices or accessories
Usable with RAM Vent-Temp, Temp Right or NFC-Repeater
Input Connector: 5.5mm DC
Input Cable Length: ca. 100 cm
Certifications: RoHS, WEEE, CE & UKCA
Additional information:
Devices shown are not included in the delivery.
Only the RAM-HOL-ZE22PU holder is supplied.
€299.96
€299.96
(ramet8tab – RAM-HOL-ZE22U)
This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET80 & ET85 2-in-1 Tablet with or without Rugged Frame and Keyboard.
To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.
The cut-outs on the buttons and ports allow you to continue using them without any problems.
The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.
The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.
An NFC repeater add-on module can be used to extend the device's internal NFC reader.
The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).
Product features RAM Mounts RAM-HOL-ZE22U:
Compatible with accessories
Easy insertion and removal
With Latch
Additional mounting plate for attaching additional devices or accessories
Usable with RAM Vent-Temp, Temp Right or NFC-Repeater
Additional information:
Devices shown are not included in the delivery.
Only the RAM-HOL-ZE22U holder is supplied.
€231.05
€231.05
(syet5chg4 – SAC-ET5X-4PPK1-01)
PowerPack battery charging station, 4 slots, order separately: power supply, DC cable, power cord, fits for: ET5X, ET4X & ET8X PowerPack
€162.17
€162.17
(zet80boot – SG-ET8X-BOOT1-01)
€237.62
€237.62
(zet80handle – SG-ET8X-HANDLE1-01)
€62.96
€62.96
(zet80sph – SG-ET8X-PENLOOP1-01)
€20.38
€20.38
(zet80sstrap – SG-ET8X-SHLDR1-01)
€47.51
€47.51
(zet80stlyus – SG-ET8X-STYLUS1-01)
Stylus, long, order separately: tether, fits for: L10ax
€118.79
€118.79
(stageit-l – Stageit-l)
Contact us and book our Staging Premium Service
€60.00
€60.00
(stageit-m – Stageit-m)
Contact us and book our Staging Premium Service
€30.00
€30.00
(stageit-s – Stageit-s)
Contact us and book our Staging Premium Service
€10.00
€10.00
(stageit-xl – Stageit-xl)
Contact us and book our Staging Premium Service
€240.00
€240.00
(syaeet8x-3c – Z1AE-ET8XXX-3C00)
€238.88
€238.88
Hoja de datos y más
* The discount refers to the original sales price.